Print the instructions before you go to purchase the materials so you will have a guide.
Click here to purchase materials
Materials List and instructions to complete one doll

187 - 18MM starflakes                                                          24 - spaghetti beads
  62 - 25MM starflakes                                                            1 - 1 1/2" doll head 
  17 - 12 MM starflakes                                                           1 - wavy discs
  24 - #3 gold or silver safety pins                                        Tacky glue (Optional)
  A pair of small pliers with wire cutters  (Optional)         2 Yards of 20 gauge wire
  1 - 3" straw hat or 2 1/2" lace hat (Optional)                      1 - Berry bead
  3 - 8MM faceted beads                                                        

 Economy package contains materials, combined with the materials listed above, to complete 1 beaded doll

Contents of Economy package
2 Yards of 20 gauge wire                    1 -Berry bead.
3 - 8MM white faceted beads that are used for the hands of the doll
Price of this package is $0.59

(1) 
On each of 12 safety pins, put on 7- 18MM starflake beads and close the pin.
 
Pin #1

(2) 
On each of the remaining 12 safety pins, put on 1 spaghetti bead and 3- 18MM starflake beads. Make sure that the spaghetti bead goes on the safety pin first.

  Pin #2

(3)
With a pair of small pliers, crimp the heads of the safety pins to prevent them from opening

(4)  
Cut a 24" strip of the 20 gauge wire. Put the wire through the tail of the safety pins and then put the beads and pins onto the wire in the order (1 through 8) listed below,  making sure that the beads on the safety pins are facing you. When I refer to pin #1 or #2, refer to the above pictures. 

                       1)   1 -  Pin #1                                          5)  1 -  Pin #2 
                       2)   3 - 25MM starflakes                      6)  3 - 25MM starflakes 
                       3)   2 - 18MM starflakes                      7)  2 - 18MM starflakes
                       4)   1 - 25MM starflake                        8)  1 - 25MM starflake
 Continue this sequence until you have  12 safety pins,  48 - 25MM starflakes and   24 - 18MM starflakes on the wire, and again making sure that the beads on the safety pins are facing you, as illustrated in the picture to your right.

  

(5)  
Twist  the 2 ends of the wire together, using your pliers, to make a nice tight circle making sure that the beads on the pins are facing outwards. Be aware, that when twisting  the wires together, there is a breaking point. When you are sure that the circle is tight enough, cut off the excess wire with your pliers, making sure that you have a small piece of the twisted wire to tuck inside the circle.

(6)
Cut a 16" strip of 20 gauge wire and put it through the head of a safety pin in the circle of pins and beads that you have just finished. If you put the wire through the head of a pin #1, in the circle you have just finished, take a loose pin #2 and put the wire through its head. Put 3 - 18MM starflakes on the wire then put the wire through the head of the next safety pin in the circle you have finished. Continue this sequence making sure that you alternate adding pins #1 and pins #2.
After adding 12 safety pins and 36 - 18MM starflakes, cut a 6" strip of wire and put the wire through the tails of the pins you just added. Twist the ends of the wires to make a tight circle and cut off the excess wire. 

(7)  
Cut a 7" strip of 20 gauge wire. Put the berry bead on the wire and bend the wire in half so that the bead will be resting in the middle of the wire. Turn your above finished circle of pins  upside down and insert the wire end of the wire, with the 20MM berry bead on it. 


Bottom view
(8)
On the wire that has the 20MM berry bead , put on a wavy disc and 5 of the 25MM starflakes. 
Wavy Disc		 (9)
Cut an 8" strip of wire and place it between the 2 wires as shown in the picture at the right. 

 

(10)  

On the double wire that is sticking up, put on 1 - 25MM starflake, then 1-18mMM starflake and then 1-12MM starflake. 
(11)
On one of the wires that is sticking up, put on an 8mm faceted bead. Then take the 2 wires and twist them together. Cut off the excess wire but leave a little of the twisted wire and do not tuck it in, leave it sticking up. View picture below.

(12)
On each of the arm wires that are sticking out from the body, put on the following beads in the order that is listed.
1 - 18MM starflake
 3 - 25MM starflakes
1 - 18MM starflake
 8 - 12MM starflakes
1 - 18MM starflake
1 - 25MM starflake
     1 - 8MM faceted bead

(13)
Curl the wire at the end of each arm, with your pliers, 
enough to prevent the 8MM faceted bead from falling off,  and then cut off the excess wire.
If you attach rosebuds to the hands, twist the wire from 1 hand around the rosebuds then twist the wire from the other hand around the wire from the hand that you attached the rosebuds to. 

(14)
Place the doll head over the the 8MM faceted bead that is on top of the body.
(15)
 If you wish, you can glue a 3" straw hat or a 2 1/2"  lace hat on the finished dolls head and add rosebuds to the hat.